Toilet hookup line

toilet hookup line

How do you connect a toilet to the water supply line?

A toilet water supply line needs to be connected to the homes water supply. There should be a shut off valve at this location, but not always. If there is not shut off valve, you will likely need to shut the main water supply off for the house to work on it. Toilet water supply lines require a 3/8 compression fitting at the valve.

Can I use a toilet supply line for a sink?

See the article on Toilet Supply Line Fittings for information on getting the supply line connected correctly. Obtain a flexible toilet water supply line that is close to the length you need. Do not get a supply line for a sink, it will not work on a toilet. One end of a toilet supply line is much larger than a sink line.

How does a toilet work in a plumbing diagram?

How a Toilet Works – Toilet Plumbing Diagram One of these devices—called a ballcock—is connected to the water supply and controls delivery of water to the tank. When the tank’s water rapidly drops down into the bowl (upon a flush), the pressure causes the bowl’s waste water to go down the drain.

How to install a toilet with a 16-inch supply line?

When in place, put a washer and a nut on each of the bolts pointing upwards into the toilet and secure in place. Make sure this is done securely and that the toilet doesn’t wobble. Take one end of the 16-inch supply line and screw it into the back of the toilet tank.

How to install a water connection for a toilet?

How to Install a Water Connection for a Toilet 1. Choose an existing cold water pipe into which you can tie the toilet supply line, and shut off the water to that pipe. 2. Cut into the pipe at a convenient spot close to the new toilet with a pipe cutter. Place a bucket under the pipe to... 3. Solder ...

Where does my toilet water supply line connect to?

Your toilet water supply line connects to your homes water supply and to the toilet tank. Do you have a different Problem? See Plumbing Repair or How to Fix a Toilet for a complete listing of related topics.

How do you hook up a toilet to a compression hose?

The valve needs a 3/8-inch compression outlet to fit a standard toilet connection hose. 1 Choose an existing cold water pipe into which you can tie the toilet supply line, and shut off the water to that pipe. Open any faucets connected to the pipe and leave them open while you connect the toilet line to it.

How to tighten a toilet water supply line?

A flexible toilet water supply line is a little easier to tighten. It is still a good idea to use two wrenches. This is just to make sure that you dont damage anything else.

When the tank’s water rapidly drops down into the bowl (upon a flush), the pressure causes the bowl’s waste water to go down the drain. The drop in water level is sensed by a float, ball, or pressure gauge, and this triggers the ballcock to refill the tank. What is a flapper valve?

How do you install a toilet supply pipe?

Insert the pipe into the hole and fasten the elbow with screws to the wall, in correspondence to the 8-inch mark you measured earlier. You can now decide whether you want to install a pipe extending from the floor supply line toward the center of the toilet or use a flexible water supply hose to connect the supply line to the tank.

How high should a toilet water supply line be installed?

The first thing to do when installing a new toilet water supply line is to determine its location. The pipe should be located about 8 inches from the toilet center line and end about 8 inches above the finished floor.

What size compression outlet do I need for a toilet?

The valve needs a 3/8-inch compression outlet to fit a standard toilet connection hose. Choose an existing cold water pipe into which you can tie the toilet supply line, and shut off the water to that pipe.

How do you connect a toilet line to a cold water pipe?

Choose an existing cold water pipe into which you can tie the toilet supply line, and shut off the water to that pipe. Open any faucets connected to the pipe and leave them open while you connect the toilet line to it. Cut into the pipe at a convenient spot close to the new toilet with a pipe cutter. Place a bucket under the pipe to catch water.

Related posts: